Touch Panel Display MT-300

Model

MT-300

Type

Dot matrix LCD panel

General specifications

Rating

Power voltage

24 VDC +10%, -5%

Current consumption

0.6A or less

Structure

Panel-embedded type, dustproof and splashproof (excluding the internal workings that are embedded in the panel)

Insulation resistance

5 MΩ or more (tested with a 500 VDC megger) between the external terminals and the case

Environmentalresistance

Operating ambient temperature

+5 to 40°C

Operating ambient humidity

35 to 85%RH (no condensation)

Operating environment

Minimal amount of dust and corrosive gas present

Withstand voltage

1,500 VAC for 1 minute (between the external terminals and the case)

Vibration resistance

10 to 55 Hz, 1.5 mm double amplitude for 2 hours in each of the X, Y, and Z directions

Noise resistance

1,000 Vp-p, 1 µs (power supply line, common mode)

Weight

Approx 1.5 kg (excluding the connector and cable)

I/O unit specifications

Parallel Interface

Data input Page strobe input Address strobe input Data strobe input Function strobe input Area strobe input Data digit specification Count/reset input

Input rating

24 VDC, 7 mA

Minimum ON voltage

19V

Maximum OFF current

2mA

Minimum input pulse width

10ms

READY output Alarm output

Output

NPN open collector

Rated load

30 mA maximum (24 VDC or less)

Function Switch output

Output

NPN open collector

Rated load

30 mA maximum (24 VDC or less)

Output time

Output is generated while the switch is depressed.

Parallel interface

Counter input

Input rating

24 VDC, 7 mA

Minimum ON voltage

19V

Maximum OFF current

2mA

Minimum input pulse width

10ms

Highest counting speed

10 c/s (with contacts and without contacts, shared)

Serial Interface

Serial I/O (RS232C, MELSEC, SYSMAC) D-SUB 9P

Input rating

24 VDC

Synchronization between the transmitter and receiver

Start-stop (full duplex)

Transmission code

ASCII

Stop bit length

1 bit, 2 bits (switchable)

Parity check

None, even, odd (switchable)

Baud rate

1,200, 2,400, 4,800, 9,600, 19,200 bps

Rear terminal

Serial I/O (K-LINK)

Applied standard

K-LINK

Synchronisation between the transmitter and receiver

Start-stop (half duplex)

Transmission code

Binary

Data length

Fixed to 8 bits

Stop bit length

Fixed to 2 bits

Parity check

Odd

Baud rate

312.5K bps

Buzzer line out output

2.5 Vp-p, 1 kΩ

Display panel specifications

LCD display panel

Effective display area

160.0 (W)x90.0 (H)mm

Number of dots

320 (W) × 192 (H) dots

Dot size

0.46 (W)x0.41 (H)mm

Dot pitch

0.50 (W)x0.45 (H)mm

LCD life span

50,000 hours^*1

Backlightlamp

CFL (cold cathode tube) in-line thrubeam type, 10,000-hour life or more (20,000 hours average)^*1 (25°C)

Display characters

x1/4

8 x 8 dots

213 characters (alphanumeric, katakana, symbols)

Half-width

8 x 16 dots

Full-width

16 x 16 dots

2,965 characters (kanji (JIS standard 1)), 698 characters (alphanumeric, hiragana, katakana, Greek characters, Russian characters, symbols, special symbols), 20 characters (custom^*2

x2, vertical

16 x 32 dots

x4

32 x 32 dots

x6

32 x 48 dots

x9

48 x 48 dots

x16

64 x 64 dots

x25

80 x 80 dots

Internal registration screen

Main unit built-in SRAM

400 screens maximum (1 file) + 1 screen (initial screen)^*3

External registration screen

Memory card SRAM (128 kB)

886 screens maximum (6 files)^*4